Category: Energy Saving at Home

Practical ways to cut electricity, heating and water use at home, including backup power.

  • Benefits of an Energy Audit

    Benefits of an Energy Audit

    Have you ever wondered just how efficient your home is when it comes to energy? Well, this is exactly what an energy audit will tell you. Not only can these audits be used in the home, but they can also be useful for businesses attempting to save a little money in the time ahead. Energy audits can also help you to prepare your home for a transition into solar energy. Energy efficiency can come from many places including appliance upgrades and solar technology. You can learn more about the cost of solar power here.

    (more…)
  • 43 Home Energy Saving Tips

    43 Home Energy Saving Tips

    43 Home Energy Saving Tips

    No-Cost or Low-Cost:

    1.     Lower your thermostat at night and whenever the house is unoccupied. Close off and don’t heat unoccupied rooms (unless you have a heat pump). If you consistently set your thermostat back at night 10 degrees Fahrenheit, you may reduce your heating bill by 10-20 percent.

    2.     Lower the thermostat and dress warmer. As little as 1 to 3 degrees (F) makes a noteworthy difference in energy consumption.

    3.     Lower the temperature on your electric water heater to 120 (F) degrees. Turn it off when leaving for extended periods of time. Electric water heaters can be set on timers; gas heaters must be set manually.

    4.     Set refrigerator temperatures between 37 and 40 degrees (F). Clean the coils. Keep the refrigerator stocked; it takes more energy to cool an empty refrigerator.

    5.     Consider replacing your older model refrigerator, especially if older than 10 years. Older models can often use over 3 times the energy of newer models.

    6.     Wash full loads of dishes and air dry.

    7.     When washing clothes, use warm or cold water and rinse with cold. Air dry clothes, but not indoors as this creates unwanted mold and moisture problems.

    8.     Shut off lights, computers and other electronic appliances when you’re not using them. Many computer monitors have a sleep mode setting which, when activated, greatly reduces energy consumption.

    9.     Always use the bathroom or kitchen exhaust fans while showering or cooking and baking to avoid potential moisture problems.

    10.  Use a microwave or toaster oven for smaller items.

    11.  Install a low-flow showerhead. Showers use less hot water than baths; also consider takingshorter showers.

    12.  Close your fireplace damper and seal the opening shut when not in use.

    13.  During the heating season, open south-facing window coverings (e.g. drapes, blinds, etc.)

    14.  during the day. Close all window coverings at night to keep the heat in.

    15.  Install foam gaskets behind electric-outlet and switch-plate covers.

    16.  Examine and adjust, if necessary, weather stripping, door sweeps, and thresholds.

    17.  _ Install an automatic setback thermostat that adjusts room temperature according to your daily schedule. If you have a heat pump, be certain to use a special thermostat designed specifically for heat pumps.

    Steps that cost more, but pay for themselves in two years or less:

    18.  _ Install do-it-yourself weather stripping and caulking toseal air leaks. Seal all perimeter wall penetrations and ceiling and floor penetrations to stop all air movement between heated and unheated spaces.

    19.  _ Install do-it-yourself storm windows that cost less than /sq.ft. such as flexible vinyl glazing.

    20.  _ Use motion sensors or timers for outdoor lighting. You’ll still have security and save energy.

    21.  _ Replace incandescent light bulbs in common areas (where lights are on most of the time) with compact fluorescent lamps (CFLs). They use about a quarter of

    22.  the energy.

    23.  _ Replace the halogen torchiere floor lamp with a CFL model. They’re safer, use 70 percent less electricity and produce as much, if not more, light.

    24.  _ Tune up the furnace annually.

    25.  _ Replace furnace filters. The dirtier they are, the harder the fan furnace works. Clean filters are essential for heat pumps – airflow is critical and can add years to the life of your heat pump.

    26.  _ Add water heater tank and hot water pipe insulation especially if in an unheated space. Don’t cover the thermostat or, for natural gas models, the air inlets.

    27.  _ Install a sheet metal fireplace cover, especially if the flue damper does not fit tightly.

    Home energy improvements that pay for themselves in two to five years:

    28.  Increase attic insulation to R-38 (the current requirement for new homes).

    29.  _ Insulate floors over unheated spaces to R-19.

    30.  _ Insulate and seal ducts in attics, crawl spaces, garages and other unheated areas-potential big energy savings!!

    31.  _ Install do-it-yourself storm windows that cost less than /sq.ft. such as rigid acrylic glazing.

    32.  _ Perform low-cost fireplace modifications, such as fluetop damper or inexpensive glass doors.

    Home improvements that take more than five years to pay for themselves:

    33.  When it is time to replace a home appliance, purchase an energy-efficient model. These appliances cost more initially, but you will save both money and energy over its entire life. An appliance that is cheaper to purchase will have higher operating costs, and savings you’ll accumulate from using an EnergyStar appliance will be substantial.

    34.  _ Energy Star® clothes washers save energy, water, and detergent.

    35.  _ Energy Star®windows only cost ~.50 /sq.ft. more than standard windows, save energy and increase comfort.

    36.  _ Look for and purchase Energy Star®labeled electronic goods, and lighting bulbs and fixtures.

    37.  _ Add do-it-yourself insulated (quilted) window covers (minimum R-3 and costing less than /sq.ft.) or install blinds, drapes or other window coverings.

    38.  _ Wall insulation should be added especially when the wall cavity is made accessible during home remodeling. Depending on your siding type, consider blown in insulation, applied from the exterior.

    39.  _ Furnaces, heat pumps, air conditioning and water heaters all have high efficiency models available and should be considered when replacing these appliances.

    40.  _ Invest in commercially installed storm windows or insulated glass.

    41.  _ Replace conventional oil burner (oil furnace) with a more efficient flame-retention burner.

    42.  _ Install a fireplace insert or wood stove in the fireplace.

    43.  _ Install a solar water heater.

  • Energy Saving Devices: Do They Work?

    Energy Saving Devices: Do They Work?

    Even before the Global Financial Crisis rolled in waves throughout the country and across the globe, people have been looking for innovative and practical ways to conserve energy. This scenario is through even on various states like Texas where Energy Deregulation has been the norm for a considerable number of years now, giving residents the power to select their Retail Electric Providers.

    The need for energy saving measures continues to be one of the most important considerations in Texas and in various states and would continue to be a regular practice unless really cheap electricity is ever produced for mass distribution. Several energy saving devices have come out in the market in a bid to help homes and businesses achieve their aim in conserving Texas electricity. The question that arises however is whether these energy saving devices actually work or not.

    The following are some of the energy saving devices that are available in the market. Some would actually help residents save on their Texas electric bills, while others do not deliver on what they claim to do in helping save energy. It would be up to the users to study which devices would work for them and would cater to their needs, while being very careful not to fall prey to bogus devices that claim energy savings that appears too good to be true.

    * Meters and Other Monitoring Devices

    People can do a lot more if they can actually measure or monitor something and this holds true with energy. Meters are practical energy saving devices that can help you monitor your electricity consumption as well as other energy utilities. Thermostats are some of the most common and can help you monitor temperature levels of cooling appliances as well as determine poorly insulated sections of a home or a building. Gas meters and electrical meters can do the same thing, providing owners their actual energy usages and consumptions.

    Other monitoring devices can be the plug-in electrical monitor type used for individual electrical devices or appliances, or it can be a more sophisticated electricity monitor that can measure full-house usages and consumptions. Such devices are also used to monitor for any electrical leaks in appliances and lines by monitoring any drain or consumption when all known electrical devices have been turned off.

    * Indirect Home Energy Saving Devices

    These devices are originally intended for a different purpose but its use will have indirect results in energy and electricity savings. One of the best examples is a light dimmer switch. Its main purpose is to reduce the intensity of light in a particular area, but in doing so it would also result in less electricity consumed by the lighting equipment. Other devices include automatic timers, timer switches, infrared-activated switches, motion-activated switches, power bars with surge protectors, and in some more sophisticated abodes – home automation systems.

    * Direct Home Energy Saving Devices

    On the other hand, devices that are intended to conserve electricity are the direct home energy saving devices. These devices are proven to save a certain percentage of energy when used as compared to standard functioning of a device or appliances. Such energy saving devices include: programmable thermostats that can set and maintain temperature to comfortable and cost-saving minimum comfortable levels; stand-by power savers which cut power to an appliances when idle or not in use; thermally controlled switches that shuts a particular device on or off based on a pre-set temperature level; and air conditioner energy saving devices, which turns off the compressor when the cooling coils are already thermodynamically saturated.

    * Bogus Home Energy Saving Devices

    And then there are these bogus or questionable devices that claim outrageous energy savings from 10% or up to 30% or even more. These devices cost a considerable amount and can come as a plug-in device or installed through the circuit breakers. However, homeowners should be wary of using these devices and make sure that they actually save energy – which means less wattage consumption and less carbon footprint – and not just correct the inaccuracy of measurements by your power meters.

    These devices also work on inductive loads like motors only like a blender or a fan and would have no significant impact on resistive loads such as heating and lighting devices. So, it would be really worth your while to carefully study what these devices can really do before committing yourself to spending hundreds or even thousands – and have minimal impact on your electricity and energy savings in the long run.

  • DIY Home Energy Saver – Home Energy Saving Tips

    DIY Home Energy Saver – Home Energy Saving Tips

    Whether you admit it or not, with all the expenses you have in mind, no matter how big your salary is, you still want to save some extra bucks in one way or another. And the best place to start saving is right at your very home; on your power bills. Yes, your power bills.

    All your appliances and electric gadget consume electricity and pile up to your ever-growing electric bills month after month contribute to your burden as a homeowner (or a tenant on a rented place). This calls for complete information on how to start lowering your home energy consumption while not depriving yourself with all the technology you have bought.

    ·    Let us start with how well-sealed your home is…

    Ensuring that your house is totally sealed keeps your heating devices maximize its use, at the same time, save some energy. If you live on the southern part of the country, a perfectly sealed home keeps the temperature of your house maintained. This will also maximize the power of your air conditioning system.

    To do this, keep your window, sills, doorframes, and joints tight. Apply sealant on these places so that the air from the outside does not mix with the air on the inside. Whether you want to heat up or cool down your home, properly sealed house will keep your heater or air conditioning system in its best functions. You surely don’t want the warm or cold air go in and out of your home. This will consume more energy than it should be.

    Heat loss can also occur on windows. To prevent this, use plastic window cover. Plastics are best material to insulate and keep the heat of your home inside.

    A free flowing heating vents and air grills will maximize the flow of heat in your home. Keep interference such as rugs, furniture and drapes away from them.

    On moveable sections of windows and doors, you may want to use weatherstripping. Weatherstrips are rubber materials that seal the movable object from its non-moveable object. This will go on garage doors, exterior doors, operable windows, and door of attic.

    ·    Then, proceed on the blinds and drapes…

    If you want to keep your home warm during cold weather, choose drapes that would cover the windows entirely. If it is sunny, open the drapes let the sun’s heat insulate your home. In this way, you save a lot of money on heating system.

    ·    The thermostat…

    You can lower down your thermostat while you are away and while you are asleep. A centigrade lower equals to 2% saved energy. Again, you may want to turn the heating down if you are not around.

    ·    Then the laundry and dishwashing…
    You should know this: You can save as much as 85 to 90% when you turn the dial of your laundry to cold. Heating the water will consume a lot of energy. Also, you can save a lot when you wash full load. One last thing: a front loading washing machine saves you 50% on water and 50% on energy.

    Dishwashers consume the same energy regardless of wash loads. Therefore, it would be much energy efficient if you load your dishwasher full.

    ·    Go to the basement…
    Most heat is lost when your basement has leaks and drafts on the walls. Make sure you seal these places so that you can conserve a lot of heat and energy. You may also add insulation in your basement to ensure that the heat is conserved.

    One good way to know if your basement has leaks or draft is to look for spider webs. When there are web, there are leaks.

    ·    Time to go to the garage…
    Do not turn on the heating system at your garage full time. Whether you stay at your garage often or not, you can always heat it up minutes before you get in there. You can save a lot of energy if you do this. Remember: use your garage heating system only if necessary.

    ·    And finally… you electronic devices.
    Whether it is your tv, stereo, lights, or any other devices that use electricity, make sure that you turn them off when not in use.

  • Easy, Cheap Home Energy Saving Tips

    Easy, Cheap Home Energy Saving Tips

    Home energy saving tips are not just for people with old homes that suck up energy because they haven’t been well insulated or the electricity hasn’t been upgraded in 40 years. Home energy saving tips are not just for people who live in nine bedroom homes with bowling alleys in the basement. Home energy saving tips are for everybody who lives in a home.

    A few easy home energy saving tips can be found in your grocery store. The next time you are there check out the light bulb aisle. You should notice that the shape of light bulbs is really changing. Those new light bulbs are actually long lasting, energy saving bulbs that burn brighter with less wattage. Replacing all of your bulbs with the new energy saving bulbs is an inexpensive home energy saving tip that anybody can do.

    Have you ever noticed that when you turn off your television the cable box stays on, or the other way around? When you turn off your computer, do you always turn off the monitor, printer, modem, and all the peripherals that go with it? Do you have a habit of leaving your front porch light on all night just to add a little light to the bedroom in case you have to get up for something? All of these things are using up unnecessary energy.

    Some of the best home energy saving tips are the easiest ones. Put your television and computer, and all of the things that go with them on power strips that have a switch. When you turn off the TV or computer, hit the switch on the power strip and turn off all of the peripherals, too. Turn off the front porch light and open the curtains, the moon and stars will let enough light in to see by if you wake up in the middle of the night. These few, easy home energy saving tips will not only save you money on your energy bills but they will also save energy for the good of the ecology. Do your part for the going green effort, save some energy in your home.

  • Stop Wasting Electricity ? 5 Effective Home Energy Saving Tips to Save Money on Electric Bill

    Stop Wasting Electricity ? 5 Effective Home Energy Saving Tips to Save Money on Electric Bill

    If there’s one challenge every homeowner is forced to deal with on a monthly basis, it’s how to save money on their electric bill. So, if you’re one of them, these simple yet practical home energy saving tips may very well keep you from wasting electricity, and paying for it dearly, in your home.

    Based on the figures presented by the Energy Information Administration (EIA), the average monthly utility bill in the United States is about .70, with some states (such as Hawaii) paying a lot more. It’s okay if you’re really using that much energy in your home, but the truth is that you’re most probably not. Instead, you’re paying for wasted electricity – energy that you didn’t use. How annoying can that be?

    One thing’s for sure – you don’t need to pay that much to power your home.

    Fortunately, there are a lot of ways that can help you save on electricity. Here are some practical suggestions on how you can see a positive difference in your monthly electrical bill without having to break the bank.

    Seal the leaks.

    The first logical step in reducing your utility bills is to make sure that your home is not leaking energy. So, check for leaks on your doors, sills, windows, cracks on the walls, and joints. A home that is not properly insulated uses up more energy than necessary. Unfortunately, most houses built before the 1980’s belong to this category.

    To make sure your house does not leak energy, you need to insulate it properly. Seal your doors and the cracks on your walls with quality sealants. Cover your windows with plastic coating so that the heat will be contained inside your home. These simple steps can reduce the load on your heater and air conditioning system, and help you get you great savings on your next electric bill!

    Use your thermostat control wisely.

    Here’s a smart tip in using your thermostat. When you want to cool your room because the heat is getting unbearable, don’t just turn the thermostat to its lowest setting. You can’t instantly cool your room that way but it’s a great way to consume more energy than you really need!

    Remember, your thermostat will not adjust as quickly as you want to. So, whether you gradually switch it or instantly set it on its lowest, you will basically get the same result. The only difference is that you’ll spend more energy in doing so.

    Setting the thermostat several degrees lower when you are out or when you are sleeping is another great energy saving idea that can make a great difference in your utility bills.

    Be wary of seemingly small things.

    Let’s admit it – it’s easy enough to overlook a lot of seemingly small things. It’s easy to forget that you’ve left your night lights turned on for days. It’s easy to overlook that you’ve left your iPod charger, your cellphone charger, and other similar electronic gadgets plugged in 24/7. After all, they don’t consume as much energy as your other appliances, right?

    But hey, remember that these small things do add up. And these small things can add as much as 5% on your electric bill.

    Cool it down.

    Do you know that your water heater contributes about 12% on your monthly utility bill? And do you realize that you are heating water for your shower or your washing machine only to bring that temperature down by mixing it with cold water so you can actually use it? If you’re like most people who cannot use straight hot water, you can definitely get great savings on your next electric bill just by following this simple tip.

    Avoid opening the refrigerator door frequently.

    Remember how often your mom told you to keep the refrigerator door shut? Well, there’s a good reason for that – leaving the refrigerator door open increases your home energy consumption. Every time you open your refrigerator door, heat rushes in so it has to consume more electricity to maintain its internal temperature.

    Keeping these practical home energy saving tips in mind can keep you from wasting electricity and paying for energy that you haven’t used. Think of all the things you can do with the savings you’re about to get. Aren’t they reasons enough to start being more conscious on how you use energy in your home? Think about it.

  • Occupancy Sensor- A Device to Save Electrical Energy

    Occupancy Sensor- A Device to Save Electrical Energy

    With the advancement of science and technology, many things have come up with automated techniques. Occupancy sensor is one such device which can detect the presence of human in a particular area and can automatically turn on/off lighting in the specified area. This device is highly used for conservation of energy in a secured and efficient manner.

    Many commercial and industrial centers use adequate amount of power to operate lighting fixtures for sufficient illumination within the organization. The lighting fixtures are connected with lighting control systems to control the electrical energy and reduce the amount of power that is consumed by the lighting equipment. An occupancy sensor with ambient light sensor and control input is used to set on a minimum level of light to be turned on after detecting the presence of person/ persons in an area.

    Generally, occupancy sensors are designed with two technologies i.e. infrared and ultrasonic. The sensors with infrared technology can detect the human movement within the sensor’s field of view. On the other hand, ultrasonic sensors require high frequency sound to detect the motion of any person or instrument within a particular area. Now-a-days, many occupancy sensors are available with both infrared and ultrasonic techniques to offer high accuracy and flexibility in conservation of electrical energy.

    ]]>

    Many business organizations, schools and colleges use ODS10-IDW Decora Wall Mounted Occupancy Sensor manufactured by Leviton. This sensor provides automatic lighting control for saving energy and can be used for switching of incandescent lamps, low-voltage lighting with electronic or magnetic ballasts. This device is being designed with passive infrared technology to monitor room for occupancy through a segmented Fresnel lens. Besides these, ODS10-ID has been equipped with push button switch for manual control.

    If you prefer having occupancy sensor for your room or offices, then check out some online stores of electronic products. Some companies offer wide range of automation products, control systems, structured wiring, lighting control equipment and many more installation products manufactured by Belden, Leviton, Xantech and other leading manufacturers.

    You can browse their websites from your home and get detailed information about the products you are looking for. Besides occupancy sensor, you will be able to shop other electronic products like patch panel, IR receiver, wires, cables and lots more.

    Before making purchasing decision of electronic products from online stores, you can look for those websites which can offer you products on bulk. Your search for a relevant and reliable online store may help you with discounted prices on high-quality products.

    To learn more about Structured Wiring, please visit Occupancy Sensors.

    Article from articlesbase.com

    Find More Save Electric Energy Articles

  • Energy Saving Tips for Renters

    Energy Saving Tips for Renters

    You can find many ideas on how to cut back energy consumption and reduce heating and cooling costs for homes, but most of these cost cutting ideas or suggestions require that permanent items be installed within the home. For renters, those home improvement ideas are not likely to happen since the average renter has no desire to spend money on a home they do not own.

    When renting a home, if you are paying for the heat and/or air conditioning, the landlord has little or no motivation to better seal and insulate the home. With this being the case, you could choose to make these improvements on your own and save energy or you could choose to not do anything because it’s not your home, while eventually spending more money on wasted energy that it would have cost you to fix the problems in the first place. The bottom line is that it’s not helpful to purposely not improve the home just to spite the landlord or future tenants, especially if the money you spend on improvements will return to you in savings and comfort.

    Simply put, unless you know you are leaving the rental home within a year, think of the home as your home and allow yourself to realize that you will benefit by making improvements to how the home uses energy. Don’t let it matter if the landlord will reimburse you or not, because you could immediately benefit from the improvements, so don’t allow anything to hinder your choice to reduce your energy consumption.

    RENTING FOR ONE TO TWO YEARS

    1. Immediately replace all bulbs with CFL’s (compact florescent lights). This reduces power usage and offers increased lighting options at lower cost.

    2. If you are paying to heat your water and/or paying for your water, it would be helpful to replace any shower head with a water saving shower heads.

    3. Place large rolled up towels or store bought door draft stoppers at the base of every outside door during the winter months.

    4. Place a thermometer near your thermostat to help determine how accurate the device is and then make sure you do not set your temperature above 65 degrees in the winter (60 degrees when nobody is home) or below 75 degrees in the summer (85 degrees when nobody is home).

    5. Install heat shrinkable window seal kits on any window that is drafty or is single pane and has no storm windows.

    6. Be sure to remove all window air conditioners by Thanksgiving.

    7. Bleed the air from any hot water radiators or baseboard heating systems at least once per year. (baseboard heating systems may require a plumber to help with bleeding)

    8. Clean radiators or baseboard heaters to ensure better heat flow.

    9. Vacuum out the coils under your refrigerator at least once per year to reduce running time.

    10. Run a humidifier in the winter to help increase the homes humidity. This increases the capacity for the heat to remain in the home and also feels more comfortable, especially when sleeping.

    11. Use a child-safe space heater in the room that includes your main house thermostat if its practical to spend more of your time in this area. The rest of the home will be cooler since the heat will not run as often, reducing your energy consumption.

    RENTING FOR THREE YEARS OR MORE

    1. Follow the steps already covered previously for the one to two year renters.

    2. Caulk around the inside and outside of all windows and doors to seal cracks and reduce air flow

    3. Install new door seals around your exterior doors.

    4. For those with hot water or steam radiators, purchase 8×4 sheets of half inch to one inch foam board with one aluminum side and cut them one inch smaller in size than your radiator. Place the reflectors behind your radiators with the aluminum side facing forward, towards the radiator.

    5. For any section of your basement that exists above ground, grab a few rolls of R-13 fiberglass insulation and cut pieces to length to fit between the joist spaces where the basement wall top ends and the wooden part of the floor and walls meet.

    6. If you have attic access via attic pull down stairs, install an attic stair cover to seal and insulate the opening.

    7. Find the hot water piping in your basement and install foam insulation over the pipes.

    8. If you have a gas or electric water heater, purchase and install a water heater jacket.

    9. If you have an older boiler, encase it with foam board that has aluminum on one side or more.

    10. Install a dryer vent seal to reduce cold air from backing into the home when the dryer is not in use.

    11. Consider replacing your thermostat(s) with programmable types.

    You can opt to go even further with any energy saving home improvement, especially if you have some of the skills to install things on your own. For example, many years ago, I moved into a rental property that had an unfinished basement. Due to the properties landscape, the basement depth at the front and left side of the house was almost entirely underground, but the back and right side of the basement were almost entirely above the ground. My heating and air conditioning experience made it easy to see that heat was just going to be sucked through those block walls in the winter and would make it difficult to utilize the basement for anything other than simple storage.

    Having determined that I would be renting the place for at least three years, I chose to insulate the basement walls by gluing 3/4 inch foam board to the walls. With an R-Value of 5, the foam board immediately reduced my heating loss in the basement by 60 to 70%, saving me money on heating the rest of the house and making the basement suitable for more than just storage.

    It cost me several hundred dollars to make this home improvement to a home I didn’t even own, but within the next two years, I got all that money back due to reduced heating costs for the home, plus I was now able to utilize more square footage of the home for an office and playroom for the kids… without an increase in rent.

    Your capacity to save energy will improve greatly if you set aside any unproductive thoughts about how the landlord may benefit later by the home improvements you make. Instead, just focus on how this will help you save money. If you are paying for the heat, water or electricity, you will definitely benefit by making these improvements and you will save money by reducing your energy consumption. After you leave, the landlord and future tenants may benefit as well, but allow yourself to consider that to be a good thing. Our world needs to reduce its energy consumption, so if you could be a part of helping this happen, while also getting all or more of your money back in energy savings, everyone wins … and it’s great to know you are a part of that.

    David’s career highlights include authoring ‘The Rewards of Making Energy Efficient Choices’ and initiating the Weatherize America movement. He is a published author from Pennsylvania that specializes in the fields of Heating and Air Conditioning, Electrical Wiring and Interiors/Insulation. You can visit his web sites at: Weatherize America and Best Energy Saving Products

    Article from articlesbase.com

  • Saving Electrical energy Advice – 5 Methods To Save Power At Your Home

    Saving Electrical energy Advice – 5 Methods To Save Power At Your Home

    It’s not only electricity that may give us shock, electricity payments can also serve that goal equally well! In the time of recession, it is extremely important for us to try to save each possible buck on our utility bills. Power bills have a significant share among these utility payments and hence, it’s essential to guarantee that we don’t waste any electricity.

    Listed here are some suggestions that may be very useful so that you can lower your expenses on your power bills:

    Try To Use Energy Efficient Household Appliances

    Altering your light bulbs to fluorescent ones will help you decrease the cost of your energy bills. Incandescent light bulbs actually use more electrical energy than fluorescent ones since they waste more of it on heat.

    Watching Television

    One other tip to save lots of electricity as well is decreasing the extent of watching TV. Make it a habit to switch off the primary power supply to the television rather than using the remote control to switch off your TV. Reducing the extent of watching television saves you from ailments like obesity.

    ]]>

    Laundry with Hands

    Washing machines sound like your best option on the subject of laundry. Make an effort to do it with your hands if the garments are not that much and could easily wash. Or else, collect all of them and wash it one shot, using your washing machine.

    Check to See if The Electrical Systems Are Still Energy Environment friendly

    If your home is quite old, you must get an electrical contractor to examine the electrical wiring system to ensure that it is still working at its best. An inefficient wiring system will lead to costlier power payments unnecessarily, and this could amount to over 1000’s of bucks per year.

    Use Ceiling Fans

    Lastly, use ceiling fans more often as a substitute of air conditioner. Air conditioner consumes one of the most power out of all the appliances. If you want to maintain your house or room cooler, attempt to install a good ceiling fan and use air-conditioner seldom. You may be stunned to see great ceiling fans which can be found in the market. They are no longer inefficient and the new ones are are able of making a cooling and comfortable atmosphere at your home.

    Although saving electrical energy isn’t convenient and it involves some cost, it could possibly become very easy when you do it on a regular basis. It saves more of your money and it save the atmosphere too.

    Want to slash your electric bill and to save the environment as well? Check this Magnets 4 Energy Review and discover how you can build magnets free energy system with the Magnets4Energy guide, starting today!

    Article from articlesbase.com

    Related Save Electric Energy Articles

  • 10 Ways To Save Energy Bills

    10 Ways To Save Energy Bills

    Although a lot of people acknowledge they need to economize home energy to serve the environment, most are more concerned in bringing down energy consumption to lower their utility bills and spare their hard-earned income. To turn into a smart power consumer, you have to understand how you utilize energy at home and find out where you can preserve energy. Determine where the majority of your home’s energy cost is going and check where you can better energy efficiency at home.

    Here are 10 Ways To Save Energy Bills, most of which are fast and simple solutions that if put into action around the home at once could already reduce your following month’s energy bill.

    1. Check your insulation. You can perform it yourself or phone a professional. A lot of homes are not adequately insulated. Thus, energy costs for heating or cooling will shoot up. Add more insulation if you discover that you do not have sufficient. You can employ someone to do it or you can do the task yourself.

    2. Invest in a programmable thermos regulator. This device is very valuable particularly if your house is unoccupied most of the day. Program it to turn on half-hour before anyone gets home.

    ]]>

    3. Adjust your thermos regulator to a soothing temperature. In winter, save on heating costs by adjusting the temperature a couple of degrees shorter than usual. You can also save on house energy costs during summertime if you set the thermos regulator one or two degrees higher. Keeping it at a steady and comfortable temperature is a clever way to preserve home energy. If it gets a trifle cold, try lending a couple of blankets to the bed or layer your dressing before tampering with the thermostat

    4. Lower your hot-water tank thermos regulator to 120 degrees. You will still get enough of hot water but you will also salvage up to 25 kilowatt-hours each month.

    5. Substitute incandescent electric lights with compact fluorescent lamps. CFLs are more energy economical and endure for years. They also give out less heat.

    6. Check doorways and windows for air leakages. Install weather strips if you have leaky doors or windowpanes.

    7. If you are purchasing major appliances any time shortly, invest in models that bear the Energy Star stamp. This signifies that the appliance meets or surpasses the criteria on energy efficiency ordered by the United States Environmental Protection Agency.

    8. Switch off or disconnect appliances when not in function. TVs, DVD players and chargers continue to use up energy owing to their standby mode feature. Employ a power strip for these devices that you can manually switch on or off to preserve energy.

    9. Landscaping with trees and bushes that will barricade winter winds or the burning summer sun can bring down house energy costs.

    10. Conduct a home energy audited account or assessment. A careful walk-through will disclose problem areas where you could be squandering energy. Make a list of zones you have scrutinized and problems you discovered. An energy inspection will help you prioritize where you can cent re your efforts to bring down home energy costs.

    And last but not least, I’m trowing in a extra you might be interested in. A Great Innovation named Magniwork is a A Zero point magnetic power generator which can eliminate your energy bills completely. Read our Magniwork Review for more information.

    Green Energy Guru | Magniwork Review

    Article from articlesbase.com

  • The Best Ways to Save On Electric Bills

    The Best Ways to Save On Electric Bills

    Electric bills, in the summer and winter, they can be sky high. With the weather fluctuations we have been experiencing lately. After all, you can only do so much when you want to keep your home cool or warm, depending on your weather.

    So you might be wondering how to save on electric bills. After all, you can’t afford to pay for constantly increasing electric bills. It isn’t only inefficient cost-wise, but it also contributes to global warming and other environmental issues. So what can you do to not only lower your rates?

    Well, one thing you can do is to leave your windows open at night and turn off your A/C. This also allows oxygen to circulate through your house, which helps to keep you healthier since a lot of houses in this day and age are very well insulated and therefore don’t allow a lot of oxygen to get in. Airing out your house not only saves you money, but it also keeps you healthier! Unplugging unused appliances is another means of saving on electric bills.

    Then, you can do the same thing in winter. Just make sure that if you happen to live in a rather drafty house that you take the time to put towels under the doors, at the window sills, and cover any nooks and crannies that might be allowing a draft through. Then, you can turn off the heat and curl up under a few nice, big blankets. The remaining heat should help to keep you warm combined with the blankets. (Remember that it’s always better to wear/use layers because layers trap little bits of warm air and allow them to circulate, thereby keeping you warmer.) If your house is sealed, you may want to air it out once or twice a week like mentioned in the summer.

    ]]>

    If you don’t use A/C, you can keep your house cool thanks to fans. Simply place them in an open window. The window must be open or else you are just re-circulating old, hot air. A few summers ago, this caused many heat related deaths for the elderly because they were not able to or just simply did not open the windows. This will help to circulate air into the home and to make it cooler.

    These means can help you to keep your house cooler and to save on electric bills…but there is another option that you might find a bit more suitable.

    There is now a system out in the form of a box. This system acts kind of like a little bank. Why? Well, think of it this way.

    Say that you were at a restaurant and you ordered toast (or a muffin, bagel, whatever you find most appetizing) and it was very crunchy and good, but there were quite a few crumbs. So many crumbs that you were losing about 30% of your toast, muffin, etc. The bigger bites you took, the more you lost. That’s kind of how your electricity works. The current runs to your house, but it sometimes functions like the toast. You have little crumbs that are paid for, but you lose. The box acts as a type of barrier from your “crumbs” and the “floor”. It saves them. Then, when your appliance needs to be powered, instead of having to pay for more electricity, you use what you’ve already paid for and saved! This is one of the quickest, easiest, and most cost efficient ways to save on electric bills!

    <a rel=”nofollow” onclick=”javascript:_gaq.push([‘_trackPageview’, ‘/outgoing/article_exit_link/3202243’]);” href=”http://www.kvarenergypro.com”>Green Energy Savings</a> – KVAR is an energy product that saves 10 to 35% on your Residential or Commercial Electric bills. For details visit http://www.kvarenergypro.com

    Article from articlesbase.com

    Find More How To Save On Electricity Articles