Tag: Energy conservation

  • 43 Home Energy Saving Tips

    Image showing both a fluorescent and an incand...
    Image via Wikipedia

    43 Home Energy Saving Tips

    No-Cost or Low-Cost:

    1.     Lower your thermostat at night and whenever the house is unoccupied. Close off and don’t heat unoccupied rooms (unless you have a heat pump). If you consistently set your thermostat back at night 10 degrees Fahrenheit, you may reduce your heating bill by 10-20 percent.

    2.     Lower the thermostat and dress warmer. As little as 1 to 3 degrees (F) makes a noteworthy difference in energy consumption.

    3.     Lower the temperature on your electric water heater to 120 (F) degrees. Turn it off when leaving for extended periods of time. Electric water heaters can be set on timers; gas heaters must be set manually.

    4.     Set refrigerator temperatures between 37 and 40 degrees (F). Clean the coils. Keep the refrigerator stocked; it takes more energy to cool an empty refrigerator.

    5.     Consider replacing your older model refrigerator, especially if older than 10 years. Older models can often use over 3 times the energy of newer models.

    6.     Wash full loads of dishes and air dry.

    7.     When washing clothes, use warm or cold water and rinse with cold. Air dry clothes, but not indoors as this creates unwanted mold and moisture problems.

    8.     Shut off lights, computers and other electronic appliances when you’re not using them. Many computer monitors have a sleep mode setting which, when activated, greatly reduces energy consumption.

    9.     Always use the bathroom or kitchen exhaust fans while showering or cooking and baking to avoid potential moisture problems.

    10.  Use a microwave or toaster oven for smaller items.

    11.  Install a low-flow showerhead. Showers use less hot water than baths; also consider takingshorter showers.

    12.  Close your fireplace damper and seal the opening shut when not in use.

    13.  During the heating season, open south-facing window coverings (e.g. drapes, blinds, etc.)

    14.  during the day. Close all window coverings at night to keep the heat in.

    15.  Install foam gaskets behind electric-outlet and switch-plate covers.

    16.  Examine and adjust, if necessary, weather stripping, door sweeps, and thresholds.

    17.  _ Install an automatic setback thermostat that adjusts room temperature according to your daily schedule. If you have a heat pump, be certain to use a special thermostat designed specifically for heat pumps.

    Steps that cost more, but pay for themselves in two years or less:

    18.  _ Install do-it-yourself weather stripping and caulking toseal air leaks. Seal all perimeter wall penetrations and ceiling and floor penetrations to stop all air movement between heated and unheated spaces.

    19.  _ Install do-it-yourself storm windows that cost less than /sq.ft. such as flexible vinyl glazing.

    20.  _ Use motion sensors or timers for outdoor lighting. You’ll still have security and save energy.

    21.  _ Replace incandescent light bulbs in common areas (where lights are on most of the time) with compact fluorescent lamps (CFLs). They use about a quarter of

    22.  the energy.

    23.  _ Replace the halogen torchiere floor lamp with a CFL model. They’re safer, use 70 percent less electricity and produce as much, if not more, light.

    24.  _ Tune up the furnace annually.

    25.  _ Replace furnace filters. The dirtier they are, the harder the fan furnace works. Clean filters are essential for heat pumps – airflow is critical and can add years to the life of your heat pump.

    26.  _ Add water heater tank and hot water pipe insulation especially if in an unheated space. Don’t cover the thermostat or, for natural gas models, the air inlets.

    27.  _ Install a sheet metal fireplace cover, especially if the flue damper does not fit tightly.

    Home energy improvements that pay for themselves in two to five years:

    28.  Increase attic insulation to R-38 (the current requirement for new homes).

    29.  _ Insulate floors over unheated spaces to R-19.

    30.  _ Insulate and seal ducts in attics, crawl spaces, garages and other unheated areas-potential big energy savings!!

    31.  _ Install do-it-yourself storm windows that cost less than /sq.ft. such as rigid acrylic glazing.

    32.  _ Perform low-cost fireplace modifications, such as fluetop damper or inexpensive glass doors.

    Home improvements that take more than five years to pay for themselves:

    33.  When it is time to replace a home appliance, purchase an energy-efficient model. These appliances cost more initially, but you will save both money and energy over its entire life. An appliance that is cheaper to purchase will have higher operating costs, and savings you’ll accumulate from using an EnergyStar appliance will be substantial.

    34.  _ Energy Star® clothes washers save energy, water, and detergent.

    35.  _ Energy Star®windows only cost ~.50 /sq.ft. more than standard windows, save energy and increase comfort.

    36.  _ Look for and purchase Energy Star®labeled electronic goods, and lighting bulbs and fixtures.

    37.  _ Add do-it-yourself insulated (quilted) window covers (minimum R-3 and costing less than /sq.ft.) or install blinds, drapes or other window coverings.

    38.  _ Wall insulation should be added especially when the wall cavity is made accessible during home remodeling. Depending on your siding type, consider blown in insulation, applied from the exterior.

    39.  _ Furnaces, heat pumps, air conditioning and water heaters all have high efficiency models available and should be considered when replacing these appliances.

    40.  _ Invest in commercially installed storm windows or insulated glass.

    41.  _ Replace conventional oil burner (oil furnace) with a more efficient flame-retention burner.

    42.  _ Install a fireplace insert or wood stove in the fireplace.

    43.  _ Install a solar water heater.

    Enhanced by Zemanta
  • Energy Saving Devices: Do They Work?

    Donibristle Gardens. (Red sky at night) - geog...
    Image via Wikipedia

    Even before the Global Financial Crisis rolled in waves throughout the country and across the globe, people have been looking for innovative and practical ways to conserve energy. This scenario is through even on various states like Texas where Energy Deregulation has been the norm for a considerable number of years now, giving residents the power to select their Retail Electric Providers.

    The need for energy saving measures continues to be one of the most important considerations in Texas and in various states and would continue to be a regular practice unless really cheap electricity is ever produced for mass distribution. Several energy saving devices have come out in the market in a bid to help homes and businesses achieve their aim in conserving Texas electricity. The question that arises however is whether these energy saving devices actually work or not.

    The following are some of the energy saving devices that are available in the market. Some would actually help residents save on their Texas electric bills, while others do not deliver on what they claim to do in helping save energy. It would be up to the users to study which devices would work for them and would cater to their needs, while being very careful not to fall prey to bogus devices that claim energy savings that appears too good to be true.

    * Meters and Other Monitoring Devices

    People can do a lot more if they can actually measure or monitor something and this holds true with energy. Meters are practical energy saving devices that can help you monitor your electricity consumption as well as other energy utilities. Thermostats are some of the most common and can help you monitor temperature levels of cooling appliances as well as determine poorly insulated sections of a home or a building. Gas meters and electrical meters can do the same thing, providing owners their actual energy usages and consumptions.

    Other monitoring devices can be the plug-in electrical monitor type used for individual electrical devices or appliances, or it can be a more sophisticated electricity monitor that can measure full-house usages and consumptions. Such devices are also used to monitor for any electrical leaks in appliances and lines by monitoring any drain or consumption when all known electrical devices have been turned off.

    * Indirect Home Energy Saving Devices

    These devices are originally intended for a different purpose but its use will have indirect results in energy and electricity savings. One of the best examples is a light dimmer switch. Its main purpose is to reduce the intensity of light in a particular area, but in doing so it would also result in less electricity consumed by the lighting equipment. Other devices include automatic timers, timer switches, infrared-activated switches, motion-activated switches, power bars with surge protectors, and in some more sophisticated abodes – home automation systems.

    * Direct Home Energy Saving Devices

    On the other hand, devices that are intended to conserve electricity are the direct home energy saving devices. These devices are proven to save a certain percentage of energy when used as compared to standard functioning of a device or appliances. Such energy saving devices include: programmable thermostats that can set and maintain temperature to comfortable and cost-saving minimum comfortable levels; stand-by power savers which cut power to an appliances when idle or not in use; thermally controlled switches that shuts a particular device on or off based on a pre-set temperature level; and air conditioner energy saving devices, which turns off the compressor when the cooling coils are already thermodynamically saturated.

    * Bogus Home Energy Saving Devices

    And then there are these bogus or questionable devices that claim outrageous energy savings from 10% or up to 30% or even more. These devices cost a considerable amount and can come as a plug-in device or installed through the circuit breakers. However, homeowners should be wary of using these devices and make sure that they actually save energy – which means less wattage consumption and less carbon footprint – and not just correct the inaccuracy of measurements by your power meters.

    These devices also work on inductive loads like motors only like a blender or a fan and would have no significant impact on resistive loads such as heating and lighting devices. So, it would be really worth your while to carefully study what these devices can really do before committing yourself to spending hundreds or even thousands – and have minimal impact on your electricity and energy savings in the long run.

    Enhanced by Zemanta
  • DIY Home Energy Saver – Home Energy Saving Tips

    Compact fluorescent light bulb
    Image via Wikipedia

    Whether you admit it or not, with all the expenses you have in mind, no matter how big your salary is, you still want to save some extra bucks in one way or another. And the best place to start saving is right at your very home; on your power bills. Yes, your power bills.

    All your appliances and electric gadget consume electricity and pile up to your ever-growing electric bills month after month contribute to your burden as a homeowner (or a tenant on a rented place). This calls for complete information on how to start lowering your home energy consumption while not depriving yourself with all the technology you have bought.

    ·    Let us start with how well-sealed your home is…

    Ensuring that your house is totally sealed keeps your heating devices maximize its use, at the same time, save some energy. If you live on the southern part of the country, a perfectly sealed home keeps the temperature of your house maintained. This will also maximize the power of your air conditioning system.

    To do this, keep your window, sills, doorframes, and joints tight. Apply sealant on these places so that the air from the outside does not mix with the air on the inside. Whether you want to heat up or cool down your home, properly sealed house will keep your heater or air conditioning system in its best functions. You surely don’t want the warm or cold air go in and out of your home. This will consume more energy than it should be.

    Heat loss can also occur on windows. To prevent this, use plastic window cover. Plastics are best material to insulate and keep the heat of your home inside.

    A free flowing heating vents and air grills will maximize the flow of heat in your home. Keep interference such as rugs, furniture and drapes away from them.

    On moveable sections of windows and doors, you may want to use weatherstripping. Weatherstrips are rubber materials that seal the movable object from its non-moveable object. This will go on garage doors, exterior doors, operable windows, and door of attic.

    ·    Then, proceed on the blinds and drapes…

    If you want to keep your home warm during cold weather, choose drapes that would cover the windows entirely. If it is sunny, open the drapes let the sun’s heat insulate your home. In this way, you save a lot of money on heating system.

    ·    The thermostat…

    You can lower down your thermostat while you are away and while you are asleep. A centigrade lower equals to 2% saved energy. Again, you may want to turn the heating down if you are not around.

    ·    Then the laundry and dishwashing…
    You should know this: You can save as much as 85 to 90% when you turn the dial of your laundry to cold. Heating the water will consume a lot of energy. Also, you can save a lot when you wash full load. One last thing: a front loading washing machine saves you 50% on water and 50% on energy.

    Dishwashers consume the same energy regardless of wash loads. Therefore, it would be much energy efficient if you load your dishwasher full.

    ·    Go to the basement…
    Most heat is lost when your basement has leaks and drafts on the walls. Make sure you seal these places so that you can conserve a lot of heat and energy. You may also add insulation in your basement to ensure that the heat is conserved.

    One good way to know if your basement has leaks or draft is to look for spider webs. When there are web, there are leaks.

    ·    Time to go to the garage…
    Do not turn on the heating system at your garage full time. Whether you stay at your garage often or not, you can always heat it up minutes before you get in there. You can save a lot of energy if you do this. Remember: use your garage heating system only if necessary.

    ·    And finally… you electronic devices.
    Whether it is your tv, stereo, lights, or any other devices that use electricity, make sure that you turn them off when not in use.

    Enhanced by Zemanta
  • Easy, Cheap Home Energy Saving Tips

    Energy Saving Light Bulb taken by C Ford, 29 J...
    Image via Wikipedia

    Home energy saving tips are not just for people with old homes that suck up energy because they haven’t been well insulated or the electricity hasn’t been upgraded in 40 years. Home energy saving tips are not just for people who live in nine bedroom homes with bowling alleys in the basement. Home energy saving tips are for everybody who lives in a home.

    A few easy home energy saving tips can be found in your grocery store. The next time you are there check out the light bulb aisle. You should notice that the shape of light bulbs is really changing. Those new light bulbs are actually long lasting, energy saving bulbs that burn brighter with less wattage. Replacing all of your bulbs with the new energy saving bulbs is an inexpensive home energy saving tip that anybody can do.

    Have you ever noticed that when you turn off your television the cable box stays on, or the other way around? When you turn off your computer, do you always turn off the monitor, printer, modem, and all the peripherals that go with it? Do you have a habit of leaving your front porch light on all night just to add a little light to the bedroom in case you have to get up for something? All of these things are using up unnecessary energy.

    Some of the best home energy saving tips are the easiest ones. Put your television and computer, and all of the things that go with them on power strips that have a switch. When you turn off the TV or computer, hit the switch on the power strip and turn off all of the peripherals, too. Turn off the front porch light and open the curtains, the moon and stars will let enough light in to see by if you wake up in the middle of the night. These few, easy home energy saving tips will not only save you money on your energy bills but they will also save energy for the good of the ecology. Do your part for the going green effort, save some energy in your home.

    Enhanced by Zemanta
  • Stop Wasting Electricity ? 5 Effective Home Energy Saving Tips to Save Money on Electric Bill

    Globe icon.
    Image via Wikipedia

    If there’s one challenge every homeowner is forced to deal with on a monthly basis, it’s how to save money on their electric bill. So, if you’re one of them, these simple yet practical home energy saving tips may very well keep you from wasting electricity, and paying for it dearly, in your home.

    Based on the figures presented by the Energy Information Administration (EIA), the average monthly utility bill in the United States is about .70, with some states (such as Hawaii) paying a lot more. It’s okay if you’re really using that much energy in your home, but the truth is that you’re most probably not. Instead, you’re paying for wasted electricity – energy that you didn’t use. How annoying can that be?

    One thing’s for sure – you don’t need to pay that much to power your home.

    Fortunately, there are a lot of ways that can help you save on electricity. Here are some practical suggestions on how you can see a positive difference in your monthly electrical bill without having to break the bank.

    Seal the leaks.

    The first logical step in reducing your utility bills is to make sure that your home is not leaking energy. So, check for leaks on your doors, sills, windows, cracks on the walls, and joints. A home that is not properly insulated uses up more energy than necessary. Unfortunately, most houses built before the 1980’s belong to this category.

    To make sure your house does not leak energy, you need to insulate it properly. Seal your doors and the cracks on your walls with quality sealants. Cover your windows with plastic coating so that the heat will be contained inside your home. These simple steps can reduce the load on your heater and air conditioning system, and help you get you great savings on your next electric bill!

    Use your thermostat control wisely.

    Here’s a smart tip in using your thermostat. When you want to cool your room because the heat is getting unbearable, don’t just turn the thermostat to its lowest setting. You can’t instantly cool your room that way but it’s a great way to consume more energy than you really need!

    Remember, your thermostat will not adjust as quickly as you want to. So, whether you gradually switch it or instantly set it on its lowest, you will basically get the same result. The only difference is that you’ll spend more energy in doing so.

    Setting the thermostat several degrees lower when you are out or when you are sleeping is another great energy saving idea that can make a great difference in your utility bills.

    Be wary of seemingly small things.

    Let’s admit it – it’s easy enough to overlook a lot of seemingly small things. It’s easy to forget that you’ve left your night lights turned on for days. It’s easy to overlook that you’ve left your iPod charger, your cellphone charger, and other similar electronic gadgets plugged in 24/7. After all, they don’t consume as much energy as your other appliances, right?

    But hey, remember that these small things do add up. And these small things can add as much as 5% on your electric bill.

    Cool it down.

    Do you know that your water heater contributes about 12% on your monthly utility bill? And do you realize that you are heating water for your shower or your washing machine only to bring that temperature down by mixing it with cold water so you can actually use it? If you’re like most people who cannot use straight hot water, you can definitely get great savings on your next electric bill just by following this simple tip.

    Avoid opening the refrigerator door frequently.

    Remember how often your mom told you to keep the refrigerator door shut? Well, there’s a good reason for that – leaving the refrigerator door open increases your home energy consumption. Every time you open your refrigerator door, heat rushes in so it has to consume more electricity to maintain its internal temperature.

    Keeping these practical home energy saving tips in mind can keep you from wasting electricity and paying for energy that you haven’t used. Think of all the things you can do with the savings you’re about to get. Aren’t they reasons enough to start being more conscious on how you use energy in your home? Think about it.

    Enhanced by Zemanta
  • Energy Saving Home Improvements That Pay Back Quickly

    Incandescent light bulbs.
    Image via Wikipedia

    The concept of saving money by making energy efficient improvements to your home or business is nothing new, but what is new is the magnitude of money you can save, now that energy prices have spiraled upwards. Combine this increased capacity for energy savings with an increase in tax credits and grants provided by federal and state governments that can be applied to many energy saving home improvements and you have the perfect storm to motivate almost anyone to make energy efficient improvements.

    WHERE DO YOU START?

    Any plan for saving energy should always start with the simplest and most basic improvements. This is necessary to ensure your money is spent in the most productive way since the whole point is to save money and not to throw it away by spending more money than necessary for any energy saving home improvement.

    For example, if you have it in mind to add solar panels to make power for your home, but have done little or nothing to first reduce your homes electrical needs, you will require a much larger solar power system and will spends an excessive amount of money to compensate for not having taken care of the little things first.

    START WITH LOW COST METHODS TO STOP WASTING ENERGY

    Duh, but hey, this first step is often missed, and is generally the least expensive and most rewarding step as compared to obtaining the highest ROI (Return on Investment) or how much you spend versus how much you save and how quickly you recover your costs.

    Before I list any energy saving ideas, let’s put things into perspective and create a clear motivation as to why the small steps are so important and can be so rewarding.

    Let’s say you were sizing a solar power system and wanted to know how large the system should be for your home. You need to take many things into account, but for this example, let’s say we just wanted to look at your lighting needs.

    Taking a quick walk through the home reveals there are 60 light bulbs in your home. In most cases only a portion of the lights are being used at any time, but to get the best example of your energy needs, we’ll calculate that one-third or twenty bulbs would be used in all your rooms on a typical afternoon, for a total power requirement of 1600 watts.

    Since the average solar panel has an output level of 170 watts, you would need nine panels to provide 100% coverage for your lighting. At a cost of about 0 per solar panel, your total cost would be 50 — not including installation.

    Now, if you first reduce your power needs by updating your lights from incandescent bulbs to CFL’s (compact fluorescent lights), you will reduce the power needs of these twenty bulbs to one-third their previous level at a cost of per bulb or a total of dollars. Now that your lighting load has been reduced from 1600 watts to only 500 watts, you can now get by with three solar panels at 0 each for a total cost of 50 plus installation.

    As you can see, by spending on simple CFL’s, you will have saved over 00 on your solar power system… and that’s just one item, so let’s take a bold and fresh look at why we should be motivated and thankful to experience the benefits of saving energy by not wasting energy.

    As you read the list of energy saving ideas below, look past any initial expense or labor involved and see only that the benefits will always exceed the initial cost and effort. When looking at these improvements in that light, the expenses and tasks can become enjoyable, plus you can always remind yourself that in the process of saving energy, you are being very green by helping to improve the planets environment.

    Also, if you wanted even more information on the rewards of making energy saving improvements, search for my book, The Rewards of Making Energy Efficient Choices and you’ll obtain an even clearer idea of how to best go about saving energy in the most practical way.

    – Replace all incandescent bulbs with CFL’s or LED’s

    – Replace conventional dryer vent with a dryer vent seal

    – Replace bathroom exhaust wall switches with 30 to 60 minute timer switches

    – Clean the coils in your refrigerators and freezers twice a year

    – Install water saving shower heads

    – Don’t run your clothes dryer on very cold nights or on extremely hot and humid afternoons

    – Replace computer power strips with Energy Saving Smart Power Strips

    – Replace weather stripping on older doors and windows

    – Caulk any cracks around windows, doors, siding, etc.

    – Wrap your water heater and/or boiler with an insulation blanket

    – Install programmable thermostats with winter settings no greater than 68 degrees and summer settings no less than 74 degrees

    – Insulate hot water and heating pipes in your basement or any unconditioned space

    – Replace filters twice annually in your forced air heating and air conditioning systems

    – Turn off televisions when not being viewed

    – Seal off unused windows and wall cavities in basements and attics

    – In hotter climates, install curtains or shades on southern and western facing windows and close them during the afternoon until the sun sets

    – In cooler climates, be sure to open southern and western facing shades or curtains during the day to allow the suns free energy in. Close them once the sun sets.

    Most of these improvements cost less than 0 each to perform and yet they can provide significant savings throughout the year. Some of the suggestions cost absolutely nothing and simply require a change in habit. Overall, you can significantly reduce your energy use, significantly reduce your carbon footprint and enjoy a greener home and lifestyle by making these low cost energy saving changes.

    If you don’t know where to get your products or aren’t sure exactly what to look for, simply search online for the ‘best energy saving products’ and start there, but do start. Don’t put it off a moment longer and just make it so. As i already demonstrated, you’ll be happy you did.

    After you have taken care of all the minor energy saving improvements, you can opt to move onto more aggressive and more expensive items such as increasing your homes level of insulation, replacing doors and windows, upgrading your heating and cooling system and more. Since these items can take much longer to recover their costs, it would be best to have an experienced weatherization inspection performed by a Weatherize America representative so that you can determine your best options.

    David Nelmes is a published author and home energy inspector in David Nelmes is an author and home energy inspector in Pennsylvania, specializing in the fields of Heating and Air Conditioning, Electrical Wiring and Interiors/Insulation. You are welcome to visit his web site Energy Efficient Choices
    Article from articlesbase.com

    More Energy Saving Articles

    Enhanced by Zemanta
  • Electric Energy Saving Device- Everything You Should Know

    Power Factor Correction Unit. Automatic Capaci...
    Image via Wikipedia

    If you’ve seen claims that some device is going to slash your electricity bill by 10% to 25%, you may be in for a disappointment. The fact is, these Electric Energy Saving Devices, while they cut measured electricity consumption for some older electrical motors, barely put a dent in most people’s electricity bill.

     

    These devices are usually called Electric Energy Saving Device, power factor correctors, or power saving devices. They contain a capacitor, which is an electrical device that stores electrical energy for short periods between two conductors.

    You’ll read sales pages for these devices that refer to improving the power factor of inductive loads. The idea is that voltage on an alternating current line fluctuates in wave form between positive and negative, sixty times a second. A capacitor can improve the power factor (the proportion of current in the wave form that the motor actually uses) so that more of the energy you draw from the grid actually gets used to do useful work, and less gets wasted because it wasn’t needed at that precise instant. (It can be saved in the capacitor and released some tiny increment of time later.)

     

    Devices marketed as Electric Energy Saving Device or power saving capacitors are real, working devices, but claims that they might cut your power bill are misleading. The sellers usually hint at gains of 10-25% but actually guarantee nothing, and in reality your savings may only be 1-5%, not nearly enough to cover the expense of installing one of these units.

     

    There are two main types of electrical loads: resistive loads, such as lights, or anything producing heat; and inductive loads (such as an electrical motor, or anything involving electromagnetism). Unfortunately, these devices only work on inductive loads – typically electric motors – and only those that don’t already have a capacitor built into them. And if you do a load estimate for your house just by scanning all the devices you use and guessing at their wattage and hours of use per day, you’ll soon discover that inductive loads make up a fairly small proportion of your overall load – perhaps 25% or less. (You don’t run your washing machine more than a few hours a week, but some lights are on 12 hours a day or more.) So the savings you’re being promised will only apply to that small percentage of your total electrical bill.

    Manufacturers have been adding capacitors to anything with an electric motor for a number of years, because it’s one easy and inexpensive way to increase energy efficiency of those motors, thereby making the price to efficiency ratio more appealing to consumers. If you own an ENERGY STAR appliance containing an electric motor, chances are it already has a capacitor and you won’t save any electricity on that device with one of these power saving units.

     

    The sales pages for these power saving devices usually hint at potential savings but they don’t actually guarantee any particular level of savings. You’ll see claims of a range: a drop of 10 to 25% in your electrical bills. But if you look closely, you’ll see there’s no guarantee of that. Even assuming you did see a gain of 10 or 25%, how would you know whether the gain came from that or from something else?

    Look for the testimonials provided on these sites. Do customers claim to have cut power use consistently month after month while using these devices? Or is there just a claim that power use dropped by X% after the first month? Here’s an interesting scenario: say one hundred people buy such a device and install it in their home.

     

    Since everyone’s power use fluctuates month by month, even if the capacitor does no good at all, some people are bound to see a drop in power use from one month to the next, while others will see an increase. Those who see an increase in power consumption may ask for a refund for their Electric Energy Saving Device. Those who see a small gain will be moderately happy, or at least won’t complain, while the small number who, for reasons unrelated to their energy saving capacitor, see major gains, will write a glowing testimonial. The testimonial gets published, and the person who asked for the refund gets their money back but doesn’t get anything published about how badly the system ‘appeared’ to work for them. (We’re assuming, of course, that the published testimonials aren’t fabricated.)

     

    Another point in favor of this scenario (namely, where the small percentage who miraculously cut energy costs while using such a device, are the ones whose testimonials get published) is the fact that often people create the result they want to see. For example, it is well established that one of the best ways to get people to cut their electricity usage is to get them to measure their electricity usage. That’s exactly what helped my family cut our electricity usage by 50% or more: measuring our usage with an electrical power monitor (a much cheaper device, by the way, that will save you far more electricity than a power factor corrector) allowed us to see where we were wasting electricity, and we easily cut most of that waste. If you install one of these so called power saving devices expecting it will save you energy, chances are, you’ll start measuring your electricity use on a more regular basis (even just by looking at the outdoor power meter). And chances are reasonably good that your increased awareness of your electricity use will cause you or your cohabitants to be more careful about turning off lights and avoiding other big energy using activities.

    Some Electric Energy Saving Device even come with a money back guarantee. That’s great, but again, think of the hundred-customer scenario.

     

    If by fluke (or because they’re more carefully monitoring their energy use, and therefore they subconsciously cut out waste) some people see their energy use drop, they’ll keep the device, and the seller keeps the money. Others who don’t see a gain may decide not to bother asking for the refund (some people feel embarrassed when they’ve been duped) while others will get their money back. Considering that these devices are very cheap to manufacturer, a seller can profit handsomely on a 0 to 0 device even if 90% of the devices are returned. (And of course the returned devices may be redeployed to others.)

     

    As far as testimonials go, look closely at the context. One website included a testimonial from a company that ran several large water pumps. Of course, these pumps are probably inductive motors that do not have their own built in capacitor, so significant savings should be expected.

    Most large manufacturers already use larger versions of these power factor controlling devices to cut their energy costs. But your house doesn’t have dozens of 100+ horsepower motors, does it? So I would recommend you to go and get your Electric Energy Saving Device.
    Article from articlesbase.com

    More Energy Saving Devices Articles

    Enhanced by Zemanta